FREE ONLINE SPEAKER TEST

Speaker Test

A free online speaker test for your speakers and headphones. Pick your output, choose the quick check or the full set, and press play. The quick check walks through music, each speaker, bass and treble and gives you a verdict; the full set adds single frequencies, a 20 Hz to 20 kHz sweep, phase, headphone balance, surround direction and loudness steps, with live meters proving the browser is playing. Everything runs in your browser, nothing is uploaded, and the microphone is never touched.

✓No install✓No upload✓No mic access

Output and volume

The browser hides device names until microphone permission is granted, and this site never asks for it. Names may stay generic, switching still works.

50%

This slider only scales the test signal. Use your device volume keys for overall loudness, and start low before bass tones.

Choose a test

Start the speaker test

Quick speaker check

Play each item and mark what you heard. The verdict appears only when all five are marked Heard it; leaving one blank or marking Nothing gives no verdict, and neither blocks anything. Replay any item, or switch to All tests whenever you like.

Music, both speakers
Left speaker only
Right speaker only
Bass
Treble

Confirmed 0 / 5

The music is generated in your browser, not streamed: no file is downloaded and nothing is uploaded.

Output monitor

Nothing playing

Press any play button and the channel meters appear here

If the meters move but you hear nothing, the browser is playing correctly and the problem sits in your output device, system volume or hardware.

01 / METHOD

About This Speaker Test

SpeakerTester is a single page with a one-click quick check, six detailed tests and zero permissions. It exists because speaker problems show up at the worst moment, and the check itself should take a minute, not an afternoon.

Every test is built on the Web Audio API, the audio engine inside every modern browser. Tones are computed at play time, noise is filtered in memory, and the channel meters read the exact signal the page sends to your output device. Nothing is streamed, nothing is uploaded, and the microphone is never touched.

It is a listening test, not a laboratory: loudness here is relative, the sweep is not a measured frequency-response curve, and the top of the range depends on your hearing as much as your speakers. Saying the limits plainly is what makes the results worth trusting.

References

Web Audio APIThe W3C standard every generator, panner and analyser on this page is built on.
ITU-R BS.775-2The reference for stereo loudspeaker placement and listening angles.
IEC 60268-5The standard loudspeaker measurement series, useful context for what a listening test is not.
02 / TUTORIAL

How to Test Your Speakers in 3 Steps

A speaker test answers three questions: does sound come out, do both channels work, and how much of the frequency range survives the trip. The whole check takes about a minute.

01STEP

Check the output

Sound goes to whatever output your system picked last, which is often not the device in front of you. Pick your speakers or headphones explicitly and set the volume near half.

→ Output selected on purpose, volume around 50%.

02STEP

Choose how to test

Step 02 offers two ways in. The quick check plays music, then each speaker, then bass and treble, and asks what you heard. All tests hands you the six detailed tests and you drive each one yourself.

→ Mode selected, first sound coming from the right device.

03STEP

Read the verdict, then go deeper

Mark each item you heard in the quick check: five marks give a verdict. If something fails, switch to All tests and run the bass descent from 150 Hz, the full 20 Hz to 20 kHz sweep and the phase check.

→ Verdict read, bass limit found, no rattles on the sweep.

Where to check, device by device

Half of all failed tests are just sound going somewhere else. These are the exact places to look on each platform.

PlatformWhere to lookWhat trips people up
Windows 11 / 10Settings → System → Sound, or right-click the taskbar speaker iconThe browser can be muted per-app in the Volume mixer while everything else plays fine.
macOSSystem Settings → Sound → OutputThe Output balance slider drifts off-center easily and quietly kills one side. Center it.
iPhone / iPadControl Center → tap the AirPlay icon on the audio cardFlip the Ring/Silent switch if a tone refuses to play. The side buttons set the media volume.
AndroidSettings → Sound and vibration → Media volumeThe media slider also lives in the pull-down quick settings. Some phones keep routing to a paired-but-off Bluetooth device.
Any laptopThe output list itselfThe single most common cause: the laptop still sends sound to an HDMI monitor or a sleeping Bluetooth headset. Pick "Speakers" explicitly.

On laptops and phones, remember the physics: built-in speakers are small, so missing deep bass is expected behavior, not a fault you can fix in settings.

03 / MECHANISM

How This Speaker Test Works

Every test on this page is the same five-stage chain, built directly on the Web Audio API. No plugins, no downloads, and no audio files fetched from anywhere.

1

Source

A sine oscillator or a pink-noise buffer, computed live by your browser. The signal is mathematically exact, which is why it makes a fair test.

2

Gain

The volume slider scales the signal before it leaves the page. It is a relative control, not a calibrated level in dB.

3

Panner

A stereo panner routes the signal left, right or both. A spatial panner places bursts around your head for the surround test.

4

Analyser

The meters tap the exact signal on its way out, which is why moving bars prove the browser side of the chain works.

5

Output

Your audio hardware receives the signal and does the rest. Everything after this point belongs to your device.

SIGNAL CHAIN

What this test is honest about

Not calibrated

Loudness depends on your volume setting and hardware. The tool compares channels against each other, it does not measure dB SPL.

Pure, not magic

The tone is a pure sine. Any coloration, distortion or rattle you hear comes from your chain, never from the test signal.

Output only

Meters prove the browser sent audio. They cannot prove a speaker moved air. That half of the test belongs to your ears.

04 / RESULTS

How to Read Your Speaker Test Results

The quick check answers whether sound comes out at all. The six detailed tests answer why it might not. Read together they tell you whether the fault is the browser, the connection, the speakers, or simply physics.

ALL TESTS PASS

All clear

Both channels answer equally, the sweep runs clean and the bass reaches typical depth for the device. If it still sounds wrong, the remaining suspects are placement and the room.

NO SOUND / ONE SIDE DEAD

A link is broken

Meters moving without sound, or one channel silent, points at the chain: output device, system volume, cable or jack. The table below tells you which link to pull first.

BASS OR TOP END MISSING

Working as designed

Laptop speakers roll off near 100 Hz and adult hearing tops out between 15 and 17 kHz. Some results are physics, not faults. Check the table before you shop for repairs.

TestWhat you observeWhat it meansNext step
Sound testLeft and Right answer at equal loudnessThe stereo path is healthyContinue with the sweep
Sound testMeters move, but silenceThe browser is playing; the output side is notRaise system volume, check device and cable
L/R alternatingOne side never soundsBroken channel or off-center balanceCenter the balance, reseat the plug, swap cables
Pan sweepA hole or dip in the middleOut-of-phase wiring or speakers too far apartRun the polarity check below
Bass descentFades near 100 Hz on a laptop or phoneNormal roll-off for small driversUse headphones or a subwoofer for deep bass
Bass descentFull-size speakers give up in the hundredsBass driver or port problemCompare against headphones, inspect the driver
SweepA rattle or buzz at specific notesLoose part, tired surround or a room resonanceNote the frequency, inspect the driver and fittings
SweepTop vanishes above 15 kHzNormal adult hearing limitNo action needed
Volume stepsTwo adjacent steps sound identicalCompression or limiting somewhere in the chainDisable EQ and effects, test wired instead of Bluetooth
SurroundDirections blur on speakersExpected: the test renders spatial audio in stereoUse headphones for the imaging test
05 / GLOSSARY

Speaker Test Glossary: 12 Terms

Twelve terms cover everything this page can measure and everything it talks about.

HZ

Hertz (Hz, kHz)

The unit of frequency: cycles per second. Human hearing spans roughly 20 Hz to 20 kHz. One kHz is a thousand cycles.

FR

Frequency response

The range of frequencies a device reproduces, and how evenly. A listening sweep can reveal holes, but a measured curve needs a microphone.

CH

Stereo channels

Stereo carries two independent signals, left and right. Each channel can fail on its own, which is half of all speaker faults.

PAN

Stereo image

Where a sound appears between the speakers. A correctly imaged pair places voices exactly in the middle, between the two boxes.

PN

Pink noise

Noise with equal energy per octave. It sounds balanced and is the standard signal for matching speaker pairs.

SINE

Sine tone

A mathematically pure single frequency. Whatever it sounds like is your equipment, never the source.

RO

Bass roll-off

The point where small speakers lose low-frequency output. Laptops typically roll off near 100 Hz, phones even earlier.

POL

Polarity and phase

Reversed wiring flips one speaker from push to pull, cancelling bass in the middle. The polarity check on this page catches it in a minute.

HRTF

HRTF

Head-related transfer functions: how your head and ears shape sound arriving from each direction. The surround test uses them to place sounds around you.

DB

Decibel (dB)

The logarithmic unit of level. The volume test uses relative steps of 6 and 12 dB, which most people hear as clearly louder.

CLIP

Distortion

What happens when a driver or an amplifier runs out of range: the smooth wave flattens and the sound turns harsh.

BAL

Channel balance

The loudness ratio between left and right. An off-center balance slider quietly kills one side and is the first thing to check.

06 / SIGNALS

Test Tones vs Music: What to Listen With

A test signal is a known quantity. Because you know exactly what should come out, anything you hear, or do not hear, belongs to your speakers. Music cannot give you that certainty, and YouTube test videos add their own problems.

SignalWhat it isBest for
Sine toneA mathematically pure single frequency, generated live in your browserIsolating one frequency, channel tests, the bass descent
Pink noiseEqual energy per octave, so it sounds balanced from top to bottomMatching a speaker pair, hearing the whole range at once
Frequency sweepA 30 second glide from 20 Hz to 20 kHzFinding drop-outs, rattles and harsh spots in one pass
Your favorite songMastered, compressed and mixed with artistic intentA final reality check once the technical tests pass
YouTube test videosCompressed audio behind a player with ads, latency and no instant stopConvenient in a pinch, but never as precise as a generated tone

When music is still the right test

A track you know by heart is the fastest way to answer the question the tones cannot: does this system sound right? Use it after the technical tests, not instead of them. Good test tracks share a few traits:

  • Wide frequency content, from real bass to airy tops
  • Hard left and right placements you can point at
  • Dynamics: quiet passages that stay clean, loud ones that do not blur
  • A recording you have heard on at least two other systems
07 / CHANNELS

Left and Right: The Stereo Test Explained

Stereo carries two independent channels from the recording to your ears, and every link in that chain can fail on one side only. Three checks cover the whole path.

Both channels, one at a time

Playing each side alone confirms the full path: source, cable, amplifier and driver. If both sides work alone but a song feels lopsided, the recording itself is the reason.

The pan sweep

A continuous tone gliding from far left to far right should move smoothly, with no dip in the middle. A hole in the center usually means the speakers are out of phase or set too far apart.

One side silent

Reseat the plug fully, try another port and cable, and center the system balance before blaming the speaker. A mono cable in a stereo jack shorts exactly one side.

Channels sound swapped? Three fixes

If left answers from the right and right from the left, the chain crossed itself somewhere. All three fixes take under a minute:

Swap at the source

With an amplifier or receiver, physically swap the left and right cables at the amp end. Ten seconds and zero settings.

Flip it in software

Players like VLC have a stereo flip, and Equalizer APO on Windows can swap the mapping system-wide. Useful when the wiring is sealed, say a soundbar or built-ins.

Or move the speakers

If the pair is identical and symmetrical, swapping their positions achieves the same result and leaves the wiring untouched.

08 / FREQUENCY

Bass Test and Frequency Sweep, Explained

The frequency test answers one question per tone: can this system reproduce it? Knowing the bands turns "it sounds off" into a specific, fixable observation.

The frequency bands and what lives in them

BandRangeWhat lives thereNote for testing
Sub-bass20 to 60 HzMovie rumble, the deepest kick drumsOnly subwoofers reach here with useful level
Bass60 to 250 HzBass guitar, the body of the kickThe bass descent starts at 150 Hz for this reason
Low mid250 to 500 HzWarmth of vocals and guitarsBoxy, muddy sound usually means this range is boosted
Mid500 Hz to 2 kHzVocal intelligibility, snare bodyThe most important range for speech
Upper mid2 to 4 kHzVocal presence, attack of instrumentsWhere the human ear is most sensitive
Presence4 to 6 kHzClarity, consonants, string detailHarsh when boosted, dull when cut
Brilliance6 to 20 kHzCymbals, air, shimmerRoll-off with age is completely normal

Three things the frequency test will honestly tell you

Small speakers roll off

A driver must move air to make bass. Laptop speakers typically lose output below about 100 Hz and cannot reproduce 40 Hz at all. Missing bass on a laptop is physics, not a fault.

Your hearing has a range too

Young ears reach about 20 kHz. Most adults top out between 15 and 17 kHz, and it drops with age. Losing the top of the sweep is expected, not a problem.

A sweep is not a measurement

This is a listening test, not a calibrated frequency-response chart. It reveals drop-outs, rattles and hard limits. Trust a measured curve from a microphone for anything scientific.

09 / SURROUND

Surround Sound Test: What a Browser Can and Cannot Do

Surround sound means different things in a browser and in a living room, and the difference matters for what you can actually test.

A browser tab plays stereo: two channels, left and right. Physical 5.1 and 7.1 routing, meaning front center, surround back and the LFE channel, is decided by your operating system and driver before any website gets involved. No web page can certify that routing.

What a browser can do is spatial rendering. On headphones, the surround test above places short bursts in eight directions around your head using head-related transfer functions. That is a genuine imaging test for headphones, and a pleasant demo on speakers, but it is not channel certification.

To verify physical surround sound instead

  1. Windows: right-click the speaker icon, open Sound settings, click your system, then Configure, and use the built-in channel-by-channel test.
  2. macOS: Audio MIDI Setup shows the channel layout of the selected output device.
  3. AV receivers: run the receiver own test tone. It exercises every amplifier path, which no browser can reach.
10 / TROUBLESHOOTING

7 Speaker Problems and How to Fix Them

Work down this table in order. The first two rows separate a browser problem from a hardware one, which is the split the meters in the test give you for free.

ProblemWhat you noticeLikely causeFix
No sound at allMeters do not moveBrowser tab muted or wrong output deviceRight-click the tab icon in Chrome to unmute; check the system output list
No sound, meters moveSignal confirmed playingOutput device off, system volume down, broken connectionRaise system volume, check power and cables, try another output
One channel silentLeft or right alone worksBalance slider, half-seated plug, mono cableCenter the balance, reseat the plug fully, test with another cable
No bassDescent test dies earlyNatural roll-off, subwoofer off, crossover set wrongExpect laptop roll-off near 100 Hz; power the sub, crossover 80 to 120 Hz
Distortion at volumeHarshness on the sweepSmall drivers overdriven, EQ boosts stacking upTurn it down and switch off bass boost; if it persists quietly, suspect the driver
Bluetooth sounds thinWeak, noisy audioHeadset mode (mic plus speakers) forces a low-quality codecDisable call audio for that device or test with the microphone idle
Crackle and drop-outsSound cuts mid-toneWireless interference, low battery, damaged cableRecharge, shorten the distance, or test with a wire

Bonus: the one-minute polarity check

A wiring polarity error reverses one speaker, and the two sides then cancel each other in the bass. The check is quick:

  1. Stand exactly between the speakers, the same distance from each.
  2. In the test above, switch to All tests → Sound test, choose pink noise and play Both.
  3. Walk slowly sideways. If the bass keeps fading in and out, one speaker is likely reversed.
  4. Fix it at the amplifier by swapping the plus and minus wires on one speaker only.
11 / CARE

Speaker Use and Care

Speakers fail from mistreatment far more often than from age. A few habits prevent almost all of it.

Start low, always

After long idle, bring speakers up from low volume. Amplifier thump and full-level test tones are how surrounds crack and voice coils burn.

Keep them breathing

Powered speakers need airflow around their vents. Dust the grilles gently; blocked vents cook amplifiers slowly.

Respect the cables

Pull plugs by the connector, coil cables loosely and keep jacks clean. Crackling that follows the cable is the cable.

Mind the placement

Keep speakers off sun-baked windowsills and away from amplifier heat. Stability matters too: a wobbling stand buzzes at exactly one bass note.

Do

  • Bring the volume up from low after idle periods
  • Dust grilles and vents with a soft brush
  • Power everything off during storms
  • Store cables coiled loosely, not knotted

Do not

  • Run bass-heavy tracks at maximum on small speakers
  • Push headphones past audible comfort
  • Block the vents of powered speakers
  • Pull cables out by the wire
12 / MICROPHONE

Also Test Your Microphone

Half of every video call runs in the other direction. If your speakers passed today and people still cannot hear you, the microphone is the next link in the chain.

MicTester is our sister site with the same privacy promise: the test runs entirely in your browser and any recording stays on your device.

Test your microphone on mictester.app
13 / FAQ

Speaker Test FAQ

Twelve questions that cover almost everything a speaker test can and cannot do.

Start speaker test ↗

How do I test my speakers online?

Open the speaker test at the top of this page, set the volume near half and run the quick check: music, left, right, bass and treble. Mark each item you heard; five marks give you a verdict. Then switch to All tests for the bass descent and the sweep to see how much of the range your speakers actually reproduce.

Will the test damage my speakers or my ears?

No, if you start at moderate volume. The tones are ordinary audio signals and every continuous tone stops automatically after 30 seconds. Deep bass carries more energy, so lower the volume before the low frequencies and keep the sweeps short.

Why is only one of my speakers working?

Check three things in order: the system balance slider, which drifts off-center easily; the seating of every plug in the chain; and the cable itself. If one speaker stays silent on every source, the fault is inside the speaker or its amplifier.

Why can I not hear bass on my laptop or phone?

Small drivers cannot move enough air to reproduce low frequencies. Laptop speakers typically roll off around 100 Hz and phones even earlier. That is physics, not a fault. Full-size headphones or a subwoofer are the only real fixes.

Can I test 5.1 or 7.1 surround sound in a browser?

A browser tab outputs stereo, so no website can verify physical surround routing. Use the surround test here for spatial imaging on headphones, and your operating system or receiver test tones for channel-by-channel 5.1 and 7.1 verification.

Is it normal that I cannot hear above 15 kHz?

Yes. Young ears reach about 20 kHz, but the top drops with age and most adults hear 15 to 17 kHz at best. Losing the top of the sweep is expected. Only a professional audiometer can actually measure hearing.

What frequency is used for a speaker test?

Channel tests usually use 440 Hz, the concert pitch A, because every speaker reproduces it comfortably. Volume calibration uses 1 kHz, where the ear is most sensitive. The bass descent steps from 150 Hz down to 20 Hz.

Does the speaker test work on iPhone and Android?

Yes, in any modern mobile browser: Safari on iOS, Chrome on Android. On iPhone, flip the Ring/Silent switch if a tone refuses to play, and remember the side buttons control the media volume.

Why do the left and right channels sound different in volume?

Center the balance slider first. Then swap the channels: a difference that follows the cable is a connection fault, while one that stays with the same speaker or cup is hardware. On headphones, a poor seal on one side quietly kills bass first.

Is this free? Do you record or upload anything?

The speaker test is free and needs no account. All audio is generated locally in your browser, nothing is recorded, and the microphone permission is never requested or used.

Test tone or music: which is better for testing?

Tones first, music second. A tone is a known quantity, so anything you hear is your speaker and not the mix. Music is mastered and compressed, which hides problems. But a familiar track remains the best final check of whether the system sounds right overall.

My sound test failed. What should I try first?

Unmute the browser tab, which Chrome marks with a speaker icon, confirm the system output points at the right device, and raise the media volume. Those three steps fix most failed tests before any hardware is touched.

Bad sound
stops here.

One quick check or six detailed tests, one page, one minute. Check your speakers and headphones now, then send the microphone to our sister site.